Canon mp150 reset codes

MP150/MP160 ERROR CODE
E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full

E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

How to clear E27 Code

• With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
• When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
• When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
• When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in orange and green, starting with orange.)note: press 4 times for waste ink counter reset.

The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print (auto teste)
2 times Green EEPROM print (dados da EEPROM)
3 times Orange EEPROM reset (EEPROM reset)
4 times Green Waste ink counter reset (Absorvente reset)

• Turn off the printer.( it must be turn off) then turn it on again.

how to Resetting an HP laser printer

There is a abode accepted as algid resetting. It basically will set all your HP printer settings to the branch absence levels. It is important to agenda that any settings fabricated at the ascendancy console of your printer are traveling to be reset. Hence, in case you appear to accept a JetDirect agenda afresh even the IP abode will be displace to the branch defaults. You can try to displace NVRAM. To do this, about-face off your HP printer and afresh authority down the 'Go' key for about 20 abnormal while switching the printer aback on again.

- HP 1200 and 1100 models resetting: To do this, artlessly change the abstracts by traveling into the account mode. This is applicative if your HP printer has a affectation panel. Otherwise you charge to authority down the 'Go' button for about 5 abnormal while the printer is switched on.

- HP 2100 printer resetting: You charge to columnist the 'job cancel' key afterwards switching off the printer. Afresh about-face the printer on and alone afresh absolution the key alleged 'job cancel.'

- HP 2200 printer resetting: About-face off your printer and afresh authority down the 'Go' key. About-face aback the printer on while captivation the 'Go' button till the ablaze comes on. Afresh absolution the button.

- HP 6P and 5P models resetting: About-face off your printer and afresh columnist the 'reset' button and aural 20 abnormal about-face on the printer aback again.

Software Resetter Canon MP198, MP258, MP276, MP496, MP558, MP568, and MP648

Looking for software resetter tool for Canon MP198, MP258, MP276, MP496, MP558, MP568, and MP648 printer series? Luckily here it is leaked download link to grab Canon printer resetter software named service_tool 1050 to reset Canon printer series MP198, MP258, MP276, MP496, MP558, MP568, and MP648. Canon MP198, MP258, MP276, MP496, MP558, MP568, and MP648 is canon all in one printer version designed for home and small office users.

download now

New Canon Resetter 2010

This is the latest resetter for canon MP198, MP258, MP276, MP496, MP558, MP568, and MP648.

The following are the steps that must be done:

1. Turn on the printer to service mode. how to enter service mode is :

• While the printer is OFF, press and hold the Start/Stop button (Resume/Cancel in some other models).
• While holding the Start/Stop button, press and hold the POWER button.
• When the POWER LED (green light) lit, release the Start/Stop button (still holding the POWER button).
• Press the Start/Stop button TWICE (still holding the POWER button)
• Release the POWER button.
• Wait for the LCD to display 0 (zero).

1. After the display is 0, attach the printer usb cable to pc, then there will be detected new device (it's normal)
2. Run servicetool_V1050.exe
3. Confirm detected usb-port numbers on usb port column.
4. Click the MAIN ink counter reset button, make sure there is paper in the paper feed, because the printer will print after the process is complete.
5. Click platern ink counter reset button, the printer will print again.
6. Turn off the printer.
7. Your printer is ready for use again.

Download Now

Enjoy!

Reset imaging drum Q3964A in HP 2550

This is to clarify the procedure to reset the Q3964A imaging drum that is no longer working in Laserjet 2550 2550L 2550Ln. This may be somewhat of a duplicate posting, if so, sorry about that and credit goes to whoever first discovered it. This posting may help some people who were confused about this procedure or wheather it works at all.

As you know, the blinking image light for imaging drum indicates that the drum is at the end of life (according to HP) and the printer will not print. Actually, what it means is that HP is running low on CASH and is expecting you to pay for their next boat payment. The drum is probably plenty useful, and shouldn't you decide when the print quality is no longer acceptable to YOU, instead of some chip inside the cartridge with an arbitrary counter number?

Here is the procedure that will work if performed correctly (it may take several tries because timing of button presses is crucial). This procedure revived completely dead 2550L with flashing imaging drum light.

READ THROUGH THE PROCEDURE BEFORE ATTEMPTING TO MAKE SURE YOU UNDERSTAND IT! Of course, as a standard disclaimer, use at your own risk. You are responsible for the consequences, blah, blah..

1) Ensure that all printer cartridges and the drum are installed

2) Printer - OFF with power button

3) GREEN GO BUTTON - HOLD

4) POWER BUTTON ON

5) The 3 lights above the green go button will go ON and then OFF (this will happen quickly, under 10 seconds, but may vary)

6) AS SOON AS THE LIGHTS ARE OFF - RELEASE GREEN GO BUTTON

7) IMMEDIATELY - PRESS AND HOLD RED CANCEL BUTTON

8) IMMEDIATELY - PRESS and HOLD CARTRIDGE SELECTION BUTTON

9) IMMEDIATELY - RELEASE both RED CANCEL BUTTON and CARTRIDGE SELECT BUTTON

That's all she wrote.